I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi,
Is it expected to get an EINPROGRESS error when calling nrf_connect() with NRF_O_NONBLOCK set. How do I know if the call was successful or not? Should I expect a positive...
Tested with PCA10040 1.2.4 bare board Chosen p0.11 as it seems to connect nothing (floating)
I would expect the code below always prints "<info> Main: [11] 1 1 1 1 1", no...
I'm working on a custom DFU bootloader using the Secure Bootloader example in the nRF5 15.2 SDK. My board only has one LED and, during DFU, I'd like to using blinking duty...
I am using SPI 2 (not SPIM) and just migrated my project to SDK14 from 13.1.
I kept getting "Wrong configuration" on compile, until I realized that on the nrf_srv_spi.c...
Hi!
nrf52832, SDK15.0, central side. S132.
I connect my nrf52 in HID mode to android smartphon Samsung А8+ Android 9.
In a log I see connect- disconnect with error code...
Hi,
When using CFUN=0, the modem stores settings (such as system mode and successful network connection information) to the flash from what I can gather, but it then needs...
At certain times, I would like to disable the SoftDevice's control of the PA/LNA control lines and return them to normal GPIO lines.
When the SoftDevice is using the provided...
I am using nrf52832 module with SDK 11.0.0, s132. I am advertising and the central device is able to scan the advertising devices and displaying the RSSI and peer address...
Hello again Nordic World.
We are slowly attempting to transition from the nRF51 environment to nRF52. We are starting, not with development environment for our product,...
IN-119
it says t he affected versions are:" All versions of S110, S120 and S130 S132 v2.0.0"
does it means all versions of S130, or only S130 v2.0.0 affected?
When using ` nrfutil settings generate` to generate bootloader settings and merging with soft device and App, how do you then use `nrfutil pkg generate` to generate a package...
Hello, I am working on the modified versions of hrs and hrs_c examples, on two NRF52832 with s132. I modified the apps so that when they connect the peripheral reads from...
Hello,
I have a fewURGENT questions.
I have the NINA B112 by u-blox on a custom PCB (datasheet here ). We require regulatory testing of the BLE. The NINA B112 is based...
Hello,
I used to send it successfully on nRF52810.
Two chips, one as the master and one as the slave.
Using SDK15.2.0
Now, I want to port to nRF52811
Related header...