Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
HI everyone!
My case:
nRF52832 + toolbox on iOS and Android
I have device pre-programmed using seeger with settings:
Next I want to make DFU update using .zip...
I am trying to receive data from GPS L80 with the nrf52832 board but I am not able to receive anything. I connected the Rx of nrf52832 with GPS and vice versa. I also connected...
Hello, I'm trying to get manufacturer specific data from peripheral, but I don't know how to do this when the peripheral is using extended advertisement with LE Coded PHY...
Currently, I am trying to create a UART connection between the nRF52840 Dongle and my PC. I am working with the usbd_ble_uart example found in the dongle SDK. I managed to...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and Softdevice version 6.1.1
I modified the Blinky peripheral code to advertise over Coded Phy, this code is working...
Hi all,
We are working on a project that requires us to measure the resistance of something applied externally. We are mainly interested in the change of resistance over...
Hi, I have managed to send data to a dedicated server, but I have a problem with reconnection. After re-connection, this is what I get as an output. In the log, there are...
Hi, I'm using Nrf52840 as the MCU for the developed product.
For my product, there is a central and a peripheral which two are communicate with each other via bluetooth...
Does anyone have any guidelines on connection parameter guidelines for Windows 10 BLE 4.1 machines? When I attempt to set some connection parameters on the nordic 'slave/perpherial...
Hi,
I need to use 6 saadc channels to sample voltage on my project. The saadc channel 0 could be configured to connect different inputs(ANI0~AIN7).But I try to configue...
Dear,
"RECOVER" was not working properly in nRFgo Studio after tried to upgrade firmware in PCA10056.
Based on Nordic knowledge, I tried to upgrade nrfjprog to 9.7.x...
