Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am trying to port the 'radio test' example code in SDK15.3.0 from the nRF52832 to the nRF52810 so we can do some pre-certification testing of the radio in our custom design...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
To understand TWI better, I loaded 'twi_sensor' example as is on nRF52832...
Upon initial connection with iOS device, returned connection values at BLE_GAP_EVT_CONN_PARAM_UPDATE are:
ble_event: got BLE_GAP_EVT_CONNECTED. role: 1, conn_handle: 1,...
Hello,
I using the Segger with the last SDK. I modified the ble_app_uart example, I added the softdevice to the addition files. When I run the debugger everything seems...
Hey guys, Recently i decided to get the ICM-20948 DK and exploring it. I read all the info on their site and all their guides but the only briefly get over the topic, so i...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I was going to “Batter Service”. Battery level...
Hello, I am using the PCA10056 to program a nrf52811 chip on a custom board with SDK 15.3.0. I'm using the example ble_app_blinky_pca10056_s140 I am following the steps in...
I am working on transferring BMI160 sample given in zephyr samples (\ncs\zephyr\samples\sensor\bmi160) to nrf sample (\ncs\nrf\samples\nrf9160\bmi160).
Below is the changed...
I'm having a problem with the nRF52 SAADC. It's configured for
One shot operation on Channel 0 using pin Ain4.
Gain of 1/6
Tacq set to 40us
8 bit resolution...
HI,
I want to configure HT1632 LED driver using SPI communication protocol
for that i should send commands LSB to MSB
immediately data should go MSB to LSB
My question...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’ and “nRF Connect” app.
I am trying to understand...
Hi all
SDK 11.0.0 S132 version 2.0.1 nrf52832
I want to turn on the PWM and turn off the PWM after 1 minute. The device will do BLE advertising When the device wakeup...
Hi,
I have read a lot of posts about using the internal LDO/DCDC converters or using an external switch mode regulator, but haven't seen any answers I could use.
I have...
I am looking for guidance on how to fragment data in Extended advertisement on the nRF52840. I am using the "ble_app_rscs" example to advertise in non-scannable non-connectable...
Hi ,
I need to update the NRF52832 with another different module.
I can update without problem by using the nrf connect app.
I would like to use another device without...
