Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello,
I base on migration guide:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.1.0%2Fnrfx_migration_user_guide.html&cp=4_0_0_2_5...
Hello,
I found the link below and was wondering if the information is up to date (says nRF52 SDK v0.9.2 ).
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a central example. I can print the scanned RSSI, and MAC address of the each advertising packets with BLE_GAP_EVT_ADV_REPORT...
Hi, I'm trying to increase the NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to max possible (20) in my project. When I first tried to do this the softdevice prompted me with this error...
Looking to better understand bsp_indication_set.
As per the example custom_ble_service_example found on github, ...when DK is connected, LED_1 is lit and stays lit from...
Hi,
I'm developing an application for nrf52840 that's essentially based on both the USB MSC example and the BLE NUS example in SDK 14. I started with the USB MSC example...
Hi,
I am using sdk 14.2.0 ble_app_hrs_freertos example.
two threads i have created, threads are having nested loop inside.
for this case, thread is stucking inside loop...
HI:
Now i use the light_switch examples(provisioner,client,server).I need update netkey and delete node for the mesh.What is the API operate this.
SDK15.0.0
mesh2...
Is there any method to remove a single node from the network in current mesh SDK 2.1.0 with s132 soft-device 6.0?
With "config_client_node_reset" it will remove all the...
I am using the Thread Border Router 1.0.0 on a Raspberry Pi 3B+
I have not been able to connect the RaspPi to our wifi network.
I tried this method first, as described...
Hi,
I'm using the nRF52840 dongle. Using nRF Connect v2.5.0 - Programmer (experimental) tool, I've downloaded the following hex files:
softdevice_s140.hex,
ble_app_buttonless_dfu_with_bonds_s140_with_setting_page...
Hi.
I am adding buzzer beeping in Immediate Alert Service of ble_app_proximity example. Event thought Immediate Alert signal is sent from nRF Master Control, there is no...
Hi I saw example with other product like the thingy.
Do you already created app creating link with the thingy microphone and the integrated speaker, it could be nice.
...
I'm exploring an nRF51 DK board I bought using openOCD (on circuit debugger), eclipse, and the gcc/gdb toolchain under Linux.
I'm trying to understand the chip by hand probing...
