I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
Hi Nordic Team,
I would like to confirm whether enabling APPROTECT also implicitly enables Secure APPROTECT, or if these two protection mechanisms need to be configured...
Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
I would like to use the COMP capabilities.
The input is from NRF_SAADC_INPUT_AIN1.
The input voltage is 0.1-0.8V.
I would like to get interrupt every time we change...
Hello everyone,
I use sdk14.2 softdevice S132. I want to write "uint8_t some_array [7] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06};" with use fds_write and read the array from...
When using BLE_GATTS_VLOC_USER to store multi-word characteristic values that are updated by application code, what is the recommended way to prevent a partially updated value...
I am working with ble_app_uart code, in that I am trying to send continuous data over BLE. But the BLE getting disconnected while sending large data.
So I planned to have...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi all.
I've followed as much information i can find regarding RTT. I understand that it was build in to the SDK after 11 or so and I followed the guides on https://infocenter...
I use the connection event extension, but there are several concepts that I am not very clear.
Software:S132 v5.0 . SDK14.1.0 nRF52810
Goal: I need to use high throughput...
my TWI device sensor, both its writing and reading address is 0x55. This seems weird for library of nRF since the last bit should be set as 0 for transmission and 1 for receiving...
hi Engineers!
the questions - is it possible to implement multi advertising (need two) broadcasters with different advertising data use SD 140-6 (nRF52840) ?
in the new...
Our Project is based on the multiprotocol THREAD BLE dynamic example.
We have the BLE DFU also as part of our project and it is working.
We now need to add the flash storage...
Hello :)
I have a question about the timing of sending a bluetooth write request. I am using two nrf52 developement kits, one as master and one as slave. From my master...
I am porting to SDK15 and this is the error I am getting:
../../../main.c: In function 'ble_stack_init': ../../../main.c:2746:2: error: unknown type name 'nrf_clock_lf_cfg_t...
Hi,
While customising code for my application, I noticed that in on_connect method of ble_nus.c, in the p_client we set is_notification_enabled = true after checking ble_srv_is_notification_enabled...
Hi there,
I have two type nRF52 DK, pca10040 and pca10056. I know that pca10040's maximum txpower is 4dBm and pca10056's maximum txpower is 8dBm, and both boards have CR2032...
