Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
I am using sdk 14.2.0 and I want to use nrf_calendar.h in my code but it is supported only in sdk 13.0.
will you guide me how can I use it in my sdk version 14.2.0.
the...
Hi,
Would someone please help me to configure a specif channel for continuous scanning. I was browsing through the forums and understand that the SDK/SD not supports these...
Hi together,
since quite some time I try to merge my BLE application with the SPIS functionalities from nRF52 SDK 12.3 example with softdevice S132. My application should...
Hi, I am developing a central device application using the ble_app_multirole_lesc example as a baseline. I am using v11 of the SDK. This example uses the heart rate service...
I am following the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img onto the RaspberryPi 3B+.
I have loaded the...
Scan of services after connecting to DFUTarg does not return
the new services on the device. Instead the old services that existed
on the device before going into DFU...
I'm trying to follow the guide Sending mesh packets in the Interactive PyACI section on the nordic infocenter.
I've installed the required prerequisites using pip.
Here...
SDK 14.2
This question pertains to the app_timer library.
Hi,
I am using the app_timer library for creating/starting timeouts.I had a question about the APP_TIMER_MIN_TIMEOUT_TICKS...
HI,
i n this modified example: https://github.com/Rallare/nrf51_ble_app_hids_kbd_consumercontrol/tree/SDK15 cI would like to define the long button instead of short button...
Hii,
We are using currently nRF SDK12 and nrfutil for performing DFU over ble. we are able to do it by pressing button on nrf51822 Dk kit at time of restart and putting...
Hi All:
I had a problem about programming.Does someone can help me? Thanks.
My IDE is IAR :ARM 8.22.2
Projcet: nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Hi,
we are currently using nrf51822AC device and nrf SDK12 . we need to do "switching to bootloader without a system reset nrf51822" as mention in subject . actually we...
Hello, I want to send beacons from one nRF51822 device to another. My project involves using omnidirectional antennas. So, will nRF51822 be the right choice for me?
I was...
SDK 15, nRF52840, PCA10056
When I read my data in the flash I recover the before last value writen and not the last.
I'm using the es_flash.c source code from eddyston...
Hello, I want to acquire my mobile's gps sensor's information using nrf52832 dk. Can anyone please guide me how to do this ? I use keil mdk-arm5 compiler and sdk v15.
