Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
I am getteing a -12 error when trying to access a open/create a file using littlefs and a fs_open command on a nrf5340 custom board.
The filesystem seems to be mounted fine...
hi support team,
i am testing SLM demo.
i tried command as below:
[16:24:30.475] AT%XSYSTEMMODE=0,0,1,0
[16:24:30.496]
[16:24:30.496] OK
[16:24:30.496]
[16:24...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
I'm finding rather high power consumption developing freeRTOS on the nRF52. I have it found that it appears Task's are suspending properly on the main BLE thread (copied from...
Setup
I was just looking through the code in the HIDS module in more detail, now that I have built a few demo HIDS apps I want to make sure that I understand the HIDS module...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
Hi
I am using nrf52840 for indoor positioning application based on RSSI. I was wondering if somebody has a tip how to calibrate the nodes before doing the experiment.
Hi,
I'm using sdk12.3.0 ble_app_uart.
My problem is BLE connection.
Sometimes(almost 50%)I tried to connect BLE but fail and I have to connect again.
I don't know...
Hi, I'm contemplating ways to drive a small RGB LED matrix with the nrf52832 in a really space-tight project. Ideally without any external components. I'ts maybe around 40...
Hello,
I need do synchronize the time between two NRF52 devices. One is connected to the other by a custom BLE service. Do you have any ideas how this could be done?
...
I'm trying to integrate buttonless DFU with secure bootloader with bonds with the DFU.
Using SDK 14 with SD 132 v5.0.0.
Using projects: secure_dfu_ble, ble_app_hrs_freertos...
Hello:
When I try to open an example project from nordik, keil doesn't open some files and I get the following error:
"no source": Error: #5: cannot open source input file...
in main() I initialize the timer
// Initialize the clock module
ret = nrf_drv_clock_init();
APP_ERROR_CHECK(ret);
// Request the low-freq clock to start N/A for SoftDevice...
SDK v12, SD130 on 51822.
I init uart through APP_UART_FIFO_INIT, and installed uart_event_handler. UART rx/tx with an external MCU works OK while softdevice running.
...
Hi. I have some nRF51 firmware I'm migrating to the nRF52. It's a peripheral with bunch of vendor specific services, using SDK 13.0.0 and SD 132 v4.0.2.
My code builds...
Dear Nordic,
I am trying to send the sensor data via beacon. I am regularly updating the manufacture data (through which I am sending the sensor data). But while executing...