Hi all,
I'm trying to set up MCUMGR on 54L15, such that it can receive images from my border router when they're in the same Thread network. I read that we can upload images...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
If I try to compile any of the WIFI examples for the Thingy91x I get a RAM overflow error. The only exception to this is the WIFI scanning example. If I build these for any...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi,
I'm thinking of using the NRF52 for an embedded wearable sensor application.
How much flash and Ram space can I expect to have remaining approx. for my application...
I'm a bit at a loss of how to voluntarily stop advertising: My related thread says I should call sd_ble_gap_adv_stop() , but when I do, no corresponding event is raised by...
To install micro-ecc, complete the following steps:
Install version 4.9-2015-q3-update of the GCC compiler toolchain for ARM. You can use ARM's Launchpad to find the toolchain...
Hello everyone,
I am currently porting a project from pstorage to FDS.
I am testing the functionalities of FDS including create, update and delete records and I am at...
Hello,
To reproduce this problem I use these steps:
Bond to NRF51822 using Android 6.0.1 and latest nRF Connect version;
After successful bond, connect to NRF51822;...
Hi,
We are using PPK board (PCA63511), we have followed the "PPK user guide" and installed all the necessary softwares, We have made the connections and switches option...
Hello everyone, I'm Dario.
I'm trying to work with a ble nano with nordic component. My target is to receive a string via serial periferial and sending it via bluetooth as...
I am a new engineer working with nRF52 and SDK 12 using Makefile project and arm-gcc. I wrote some simple code to try TWI Master and control a i2c slave device. My question...
Hello I just bought
SKYLAB bluetooth accelerometer sensor SKB360 bluetooth low energy nrf51822 bluetooth 4.0 low energy module
skylab.en.alibaba.com/.../SKYLAB_bluetooth_accelerometer_sensor_SKB360_bluetooth_low_energy_nrf51822_module_bluetooth_4_0_low_energy_module...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
