It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
I noticed that Digi-Key had a new part number for the nRF52 DK that wasn't designated "Preview", so I assumed it might be the final silicon. However, nRFgo Studio identifies...
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello All
I'm newbe for this device. Now my customer asking multiple offline programming IC NRF51822-QFAC-R. But I'm not sure the device can support parallel programming...
Hello,
has anyone done some good testing on the connection quality between multiple nRF51 chipsets running on the S130 SoftDevice? (Using all four connections, 3 as Central...
I'm trying to merge 'ble_app_uart' and 'twi_sensor' example.
I developed twi function in 'twi_sensor' example. I add 'ble_app_uart' example file 'nrf_drv_twi.c'
and also...
nrf51822_sleep.txt
Currently i running nordic code in Arduino IDE through the library from RedbearLab : github.com/.../nRF51822-Arduino and I facing a problem in sleeping...
Hi, can anyone explain to me about this example in this link with details :
github.com/.../main.c
I'm a newbie in nordic and i found it difficult to understand this example...
I install
gcc-arm-none-eabi-4_9-2015q3-20150921-win32
make-3.81
coreutils-5.3.0
and setup the PATH in windows
then i enter CMD mode make some command to...
I am using the LFCLK RC oscillator, 8000ms calibration interval.
Is it possible to read from some register the resulting calibration value for the LFCLK RC oscillator?
Now I work on designing a product, which is implemented by sending LMP commands to a bluetooth device with nrf51822. Unfortunately, nrf51822 liberary could not provide the...
Hello,
measuring ADC signal on P0.26/AIN0/XL2 and P0.27/AIN1/XL1 doesn't work (I get constant value from the ADC not reflecting actual voltage on the pin). AIN2 - AIN7 seem...
I need to send a disconnect command from the app layer. I've seen a few other posts that say to use uint32_t sd_ble_gap_disconnect. One post had this line of code as an answer...
I am using the RBC mesh in a networking product using the nRF51422. We would like to turn the mesh on and off at selected times, say once per hour for a minute or two. I know...
Hey,
I have been trying to set up wdt for my application which services some interrupts once in a while and advertises continuously. I put the nrf to sleep using sd_app_evt_wait...