Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
In my application I need to use the whole flash memory available (128 KB of the nRF51422 QFAC). My data is first stored on a 2KB buffer and once the buffer is full, data is...
I'm trying to figure out why I need to rebond after completing a DFU upgrade with Android 5.1.
My bootloader does not modify the device manager pstorage state, but I am...
Hi!
I've just started developing with NRF51422 (PCA10028 board). I downloaded the free version of Keil MDK-ARM and loaded the "ble_app_uart_s110_pca10028" example from...
Hi,
We wanted to create a device what control with a remote controller but we want to controll this device by smartphone also.
We going to use 51822 but it is not exactly...
Hello.
Our company develop BLE device and make some applications(android/iOS) for updating ble devices.
Those applications use nordic DFU source for installing firmware...
Hi
I want to configure SAADC channel to work in oversampling mode, and to enable burst mode.
nRF52832 Objective Product Specification v0.6.2 says:
"CH[n].CONFIG.BURST...
Hi,
I'm looking to use the nRF51822 in a new design and would like to know if there is tool available to calculate how long it will be able to run of a battery when set to...
I can discover 6 services by Master Control Panel over Android device, but only 4 services on ios 9 device, I can't discover Gap and Gatt service. What's more, when i try...
Hi all,
we are using NRF24L01+ ic for our application .we want to have TAG transmitting and receiving end separated so we are using the two NRF ic .We want that there should...
Hi,
Does Nordic provide a version of nRF Toolbox or similar to run under Windows 8.1 (not Phone)?
If not, can anyone recommend any free general-purpose tools or utilities...
I encounter a problem to switch to DFU mode from UART when BLE is connected and one 5ms timer keeps running for heart rate sensing alg. Maybe it's the reason keeps BLE busy...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
