I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hello everyone,
i can able to set the static passkey but i would like to know the difference bewteen security key and passkey how can i set security key ? any suggestions...
Good day!
Faced with the problem that I didn't get to run N5 Starter Kit (nRF51422) on maximum speed in Advanced Burst Mode, using ANTware II with ANTUSB-m to read packets...
I read the multi-role project on Github. For time slot part, there's no explicit hfclk start/stop operation along with the radio events, is it possible that sd_radio_session_open...
In the nRF8001 Arduino SDK, there is a " ble_bandwidth_test " example.
It says,
"The bandwidth is measured (sic?) with the nRF UART App in the Apple iOS app store" ...
I am trying to communicate with a SPI peripheral, using the nRF52 as the master, and the peripheral as the slave. What happens is that it still faults out, and the presence...
We are currently developing an Android app (5.0) supporting the peripheral mode and communicating with the Master Control Panel (v3.7.1).
The connection to the Android...
Hi,all.i faced a problem:when i take my phone far away from my device,link lost service can work normal and my device can alarm.But if i turn off bluetooth switch on my phone...
Hello everyone,
i am trying to mix up both services proximity and RSSI but i am not able to merge the header files of these two services can anyone guide me? how to merge...
Hi,
I'm converting my project to OSX GNU from windows keil because of license problem.
There is some .o files made by keil-arm complier in my previous project.
and...
Hello,
Is that possible to force carrier frequency out of 2.4 GHz band (modify canals) for a special underwater application (2.4 GHz is not adapted so i whish to move on...
Hi,
I want to detect long and short press in same button.
Define "BUTTON_DETECTION_DELAY" can detect one delay.
Let me know to detect more than two delays.
Hi everyone,
I'd like to use the micro-esb radio interface to let to nRF's talk to each other. One of them will be generating 4 PWM outputs based on data received.
I have...
Hello Nordic,
I am trying debugging on following project [--ble_app_lbs_master--]. During debugging, I never reach at app_button_is_pushed function. I tried pressing the...
I have built a PCB that uses the nRF51822 . I am failing to load the binary onto the chip via the nRF51 DK. I can:
connect to the nRF51822 on my mac using the JLinkExe...