Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hi everyone,
We found that the LIS2MDL_INT interrupt from the compass on P1.06 affects communication between the app core and the network core.
About 3 seconds after...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
Hi , am developing the st7789v_minimal_sample application using Nrf52840. after creating minimal application am facing some unrecognisable issue. which am stuck can you please...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
Hi,
1. It was measured that SWD0_SELECT needs to be connected to VDD to program the external nRF54L15 2. Will the document or the program be modified here to make it consistent...
Hello,
I have some code running on an NRF52832 using NRF Connect SDK 2.5.1 which initalizes my BLE with a random private resolvable adress so that I can easily reconnect...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
I am using two nrf24l01+ at two ends & i am able to communicate between both but its a simplex communiacation means I am transmitting nrf code from A end & B end receives...
After programming a panel of 6 modules embedding nRF51822, I would like to send some data in order to test some features. The basic idea is to validate the modules before...
Hi,
How can I change/add include file path in the new pack SDK.
For eg: I want to port the S110 bootloader to S130. But I am not able to change the include path to the...
I am using LMT84 temperature sensor directly connected to P06 on my nRF24LE1, QFN24. Using the built-in BG reference of 1.2V, I measure temperatures from about -30C up to...
When I call the function sd_ble_gatts_sys_attr_set, the compile error "source\ble.c(142): error: #165: too few arguments in function call" showed in Keil V5. But I found just...
Hi,
I have used the following version for my development
SDK: 6
SD:s110_nrf51822_7.0.0_softdevice
nRF51822 :3.0
Recently we are using nRF51822 3.1 QFACA1 1442AB...
Hi,
I am trying to setup DFU on a PCA10001 board with the following specifications:
softdevice v8.0
bootloader: From SDK v8 examples (bootloader\pca10028\dual_bank_ble_s110...
I updated my MCP to the newest version and then the new MCP wanted to update the pca10000 with the newest firmware--> failed. Now i can't get my pca10000 to work again. i...
Hi,
i am trying to connect via bluetooth using the gatttool on a Raspberry Pi. On the Nordic device I am using the BLE Proximity Demo. Everythings work fine, but after 30...
Hello all,
I am trying to get a communication between the nRF8001 and the nRF51822 using the UART service. The nRF8001 is connected to an Arduino and is working fine. I...
I am trying to find out the issue with my nonvolatile driver. I currently try running
nrf_nvmc_page_erase((uint32_t)(page_address));
However, that doesn't seem to...
I've been testing Pre-Production samples running a firmware in which I catch any and all Error codes or Reason reasons and write them to the gpregret register to be read later...
