RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...
Hi,
Our manufacturer would like to change the recommended capacitors on the nRF51822 antenna circuit design. Here is the query:
Please check below 3 capacitors request...
I notice in the datasheet for the NRF24L01+ that the receive address needs to be programmed into the Receiver.
Our application receives data from another channel and supplies...
Hi All,
I am looking for a cost effective Chip Socket for nRF51822. The challenge with nRF51822 is that while it is the standard QFN48 package, the pitch is 0.4mm making...
hello,
I have known that Nordic has produced new nRF51 DK which already support s130. But it seems only a demo!
What's the exactly plan of BLE 4.1 and 4.2?
When can buy...
Since windows xp isn't supported any more, I need to get the evaluation kit working with a windows 7 PC. It looks like the problem is with the USB communication. Is there...
Hello,
I am using ESB protocol and there is a definition says "#define NRF_ESB_CONST_MAX_TOTAL_PACKETS 6" so how can I use maximum total packets number? I am looking higher...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
I am using SD 8.0 SDK 8.0 and MCP 3.8 I am able to find the DFUtarg service and successfully complete the transfer of my applcation (100% complete). However, upon finishing...
Hi,
I'm doing some throughput/current consumption tests with nRF51822 (on PCA10001).
My firmware has been developed starting from hrm example. I have created a custom service...
Hello,i have nrf518822 device,program the s130 (0.9 version).The centrel connect to the peripherals ,now have a problem.When pressed button1 the {event_handle(BLE_GAP_EVT_CONNECTED...
