I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi,
i need to use a watchdog in my application. I read that i can use the build in one, but i thing my configuration or the usage of the watchdog is wrong.
here is my config...
Hi guys,
I am getting started with your nRF51822 dev Kit. I got the nRFGo Starter Kit (nRF6310 Rev 1.4 mother board) as well. Most of the examples work as expected. But...
Hello,
I'm trying to do a millisecond counter using app_timer but the callback is never called. I think I have missunderstood how it works.
I've tried using the app_timer...
Hi,
Im trying to send 20 packages of 30bytes each as fast as possible, so I created the following loop:
for( pack=0; pack<20; pack++)
{
w_tx_payload_noack(30, MegaBuffer...
Hi all,
I have a custom board with the Nrf51822 BLE chip and it works in broadcasting mode without connection only. Basically it sends the advertising data on an established...
Hi
I have some problems about using your Master Emulator API. I want to write a dynamic link library with C++, but I don’t know how to invoke the MasterEmulator.dll.
The...
I'd like to use LPCOMP. I'd like to get rid of the 12K pulldown on SWDIO.
I can tell from PCN-082 that QFAA CA and C0, as well as QFAB AA and A0, will let me do that. ...
hello,
I know the ble device ,have central and peripheral and have some name(server/client and Observer/ Broadcaster).
The peripheral(server) has data that is needed by...
I put the boot loader at 0x3a800 and the application at 0x27400. the region from 0x14000 to 0x27400 is all blank (0xff). also
nrfjprog --memwr 0x10001014 --val 0x0003a800...
Hi,
I need to pair with the master after pressing the button in my slave device, instead of asking for passkey. Through the master control panel, i can able to see that,...
Hi,
Actually in our application we have connect accelerometer sensor to Nordic by SPI. I'm calculating power consumption for it. In datasheet it's mentioned for SPI Data...
Hello to everyone,
My problem/question now is about the MasterEmulator. I´m working with the nRF51822(SoftDevice) and i have my own program already working more or less...
Hi
I am a newbie to the bluetooth technology. I want to ask some questions:
How to apply a LLS(lost link service) profile to a bluetooth module?
Can I buy the...
After reading devzone.nordicsemi.com/.../is-there-any-differences-between-nrf51822-and-nrf51922 and the literature around nRF51922, I'd like to know if there's going to be...
