Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Is possible to put S110 in observer role (as peripheral) , waiting for a specific advertising (or waiting for an active scanning) and then switch to advertiser role (always...
Hello all,
I'd like to use NRF UART App sample code (newest iOS7 version) to send data from iOS6 to nrf51822 for "real time" data transmission. But I found that when I...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
Hi experts,
i found one issue that if i continue to make the 51822 advertise(if advertise timeout, start again), sometimes the 51822 will stop in somewhere. I'm sure that...
I have just acquired the NRF51822 Evaluation Kit and going through the getting started documentation. I can't seem to fix a compiler error which is highlighted in Kiel uVision...
Hi,
I am starting my first project with nRF51822 for my thesis.
I thought its a good idea to start with evolution kit so I bought nRF51822-EK
I assume I will get everything...
Hi, I'm trying to run your ble_app_hrs on your nrf51822 chip using internal rc clock: NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION, so I pass this to the BLE_STACK_HANDLER_INIT...
Hello,
I have just bought an NRF51822-EK to familiarize myself with the micro-controller for a potential future job. Admittedly I feel like I am completely in over my head...
I've made a custom board with an nRF51422. The nRF51 part follows the reference schematics almost identically. After overcoming some reflow issues this board seems communicate...
where is nRF51822 example code appropriate to "nRF Temp App" ?
I have successfully installed "nRF Temp App 2.0" on Nexus 7 with Android 4.3.
Now I would like to run the...
Hi,
I want to install the nrfgostudio_win-32_1.15.1_installer,but is's fail.nrfgostudio V1.14 can be installed sucessfully.I still use the command line to install the nrfgostudio...
