Hello,
We are looking for a developer a single task project. We need to provide all of our developers with the same development environment, so we are looking for someone...
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi Nordic,
As far as I can see, there is BLE_NUS_CONFIG_LOG_ENABLED defined for ble_nus in sdk_config.h. However, I cannot find the similar BLE_NUS_C_CONFIG_LOG_ENABLED...
Hi, can we use a manufacturer name of our own for the usb in nrf52840?
We know that we can still use the Nordic Semiconductor's usb vendor in a commercial product.
Best...
Hi, Can I use nRF24LE1-F16Q24-DK without nRFgo Starter Kit? If yes please suggest me programmer to program nRF24LE1 by Keil IDE. by referring documentation I found its support...
Hi
SDK v15.2.0 SD 6.1.1
I have managed to send out "Connectable, Non-Scannable" extended adverts with some AD packets as payload. On a frontline sniffer as per the file...
I am developing a HID keyboard based on an nRF51822.
The firmware source available here:
https://github.com/martonmiklos/ble_keyboard_fw
(It is based on the ble_sdk_app_hids_mouse...
Hello,
i'am trying to control the pwm Idle State Level.
between my Sequence's (1sek) the PIN stays High But i need it low.
I try to set the GPIO Out Register, but...
Hello,
I am working on a simple Bluetooth mesh example setup with the following configurations:
nRF52832 DK: light switch server, subscribed to group 0xC000
nRF52840...
We have a mobile app on iPhone and Android, the NRF52 advertises every 3 seconds. The app can discover the NRF52 quickly but it takes a long time to connect. The iPhone is...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
Hi!
I'm trying to use the AWS-FOTA sample, I flashed the sample onto the board and it connected to the AWS account successfully, but when I try to add the update.bin file...
Hi. The main loop of my app is mostly doing SPI communication to a GPS receiver. I'd like it to do that every second or so and spend the rest of the time in system on but...
Is it possible to configure the ACL to protect the UICR registers?
If so, would this have any impact on the SoftDevice or other nRF52840 peripherals? I.E does the SoftDevice...
