Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I am using nRF52840-MDK and connect to my Ubuntu running in VMWare. When I connect this device to my laptop and run pyocd-flashtool. I am getting a error message stating ...
Hi
I have purchased an nRF52832 DK to develop a human fall detection device. I'm a newbie to embedded studio, and nordic products. I just started to understand things on...
Hi, I have seen a few similar questions to this but the answers weren't too clear...I am trying to use both the long button push and the button push actions to generate separate...
Hello,
I have a Raytac MDBT50Q-RX USB dongle that I want to evaluate.
The dongle comes with Raytac's own test firmware.
In order to evaluate it for my purpose, I wanted...
I am very new begginer and dont know where to start about nordic nrf52832 chip. Started a week ago with downloading SDK and playing with examples in it.
I in specific need...
This is the structure.I am using bitfields here, even if i don't the problem still exists.
struct CODE_T
{ uint32_t guest_code_start_time; uint32_t guest_code_end_time;...
Hi,
Lior Neumann and Eli Biham found a vulnerabilitiy in BLE secure connections, to which CVE-2018-5383 was assigned.
Is the S132 SoftDevice affected by this vulnerabilitiy...
Hi Everyone
My requirements are as follows
1. I am running 4 tasks using free rtos in which one measures the ADC , 2nd sends the adc data over BLE and 3rd check if the...
hello
I am using sdk 15.3 example code of DFU (secure_boot loader \ pca10040_ble)
I want to debug code but i can not.I getting error like that "Error Flash Download Failed...
Hello,
I have been using this method for a while now and everything seemed to work. But for one of my device the method returns the error 0x3400. I wanted to know where...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
I am trying to share ADC output to Bluetooth device. But issue is as I am getting SAADC output via SPI protocol.
Now i have added SAADC+SPI in BLE app uart example, So when...
Hi there,
I want to do scanning existing networks and for these goals, I need to enable Commissioner on Commissioner side. I use the otCommissionerStart function but when...
I am looking for an example that can work with Android 6 and higher
Current examples on Github have compilation problems probably using older gradle.
The application need...
Hi,
I'm wondering why SES 4.18 requires an entire rebuild of an application each time a project is (re)opened? I would have though it would perform an intelligent incremental...
