Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
Hello, As part of an effort to migrate applications to nRF5415 devices, I've encountered voltage sensitivity issues when using existing sensors (bme688, bme280). After reviewing...
We have designed two custom boards based on the nRF52840.
Board #1 (Demo board) This board works correctly. It uses a standard 32.768 kHz passive crystal connected to XL1...
Is it possible to enable the Segger Flasher ARM Targer power supply using nRFutil?
We are now using a Segger Relay adapter , but this needs the Flasher's ARM target supply...
Looking for base examples for a push to talk using this dongle board and GATT. I choosed Peripheral LBS
Other basic example (Beacon, Blinky etc) compiled and work w/o problems...
Hi,
We want to set the PMIC's battery discharge limit via the registers BCHISETDISCHARGEMSB and BCHISETDISCHARGELSB to 1200mA but the nPM1300 PS does not describe how to...
Hi!
We're assessing the EN18031 compliance, and would like to know if there's any plans for product certification with nRF9151?
I found that the certification was...
Hi, I was checking the HAL for SPI in master mode and notice that when pm_device_action_run(<spi_device>, PM_DEVICE_ACTION_SUSPEND); the CS pin isnt changed since it status...
I want to migrate my project (for a custom nrf5340/nrf7002 board) from NCS2.9.0 to NCS 3.2.0, to hopefully get the wifi WPA Enterprise functionality to work. This is an existing...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following error message:
fatal error: nrf.h: No such file or directory
"nrf.h" is now located...
Hello, I'm using Nordic Central HR example. I'm wondering how to read RSSI of a BLE device connected to the NRF5340, I have tried multiple version found on this forum, but...
Howdy,
I am trying to connect a Waveshare BME280 to my nrf9160dk, and it's not obvious which jumper goes where. The documentation states:
Wire color
Sensor board...
hi,
i'm new with the nrf9160DK so can you please guide me to how can i start and config my nrf9160Dk with my laptop from scratch because this video is not helping me https...
Hello:
I created an app.overlay. Here it is:
/ { aliases { fra_sw = &fra_sw0; }; fra_sw0: fra_sw0 { gpios = <&gpio0 0 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; label = "FRA_SWITCH...
Hello,
We have a dual-purpose connection in our design where the signal can be either an analog input or a digital output. We have done some testing and can see that we...
