hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
The customer, T&D would like to registrate their product to Bluetooth SIG.
Then, design number shoule be required, however, regarding SDK3.0.2, there isn't any...
I am working on an nRF54L15 project and started from: C:\ncs\v3.0.2\nrf\samples\bluetooth\peripheral_uart as the base. I would like to trigger an interrupt once every second...
In the reference schematic design of the 54L, why does the RF circuit use three LC circuits? What is the purpose? This approach would likely result in higher insertion loss...
I have made a PCB using a BL5340PA module, to start i have tried a simple code to see log from RTT using the SWD SWCLK pin, i am using an NRF5340 DK as debugger/programmer...
Hi apparently the examples are not working out of the box. I do not see any documentaiton on what has to be done for them to work. Can you advise me on what i shoud do to...
This table for the absolute maximum ratings isn't clear.
Can you help confirm the unit "y" here for RRAM retention? Is this years? Is it cumulatively years or consecutive...
I am experiencing an issue with my nRF52840 DK board. When I initially connect the board to my PC via USB, the debugger LED (LED5) blinks briefly but then turns off. Additionally...
Hi,
I'm looking for some guidance.
I'm using a HolyIoT nRF54L15 dev kit to evaluate their nRF54L15 module.
I am currently looking power consumption.
I have tried the...
I'm wanting to repetitively read the SPI buffer as a master to check a status bit. I figure there's no sense in using the DMA when I can read the SPI RXD buffer directly....
Hi
I am trying to use the two GPIO pins. One GPIO pin is configured as a input and connected externally to a button.
The second is configured as an output pin. I want...
I am trying to complete the course "nRF Connect SDK Fundamentals" using a nRF52840 DK board (version 3.0.0) connected to a Mac Mini (Intel processor) running macOS version...
Hello,
I'm experiencing high current consumption with Zephyr OS. I'm using SDK 3.1.0 and the device still draws about 900 µA, and I don't know why. Although I have a custom...
Hi all, I am going through the beginner course and am using the MPU-6050 over I2C. I am able to communicate with the board where I get the WHO_AM_I. I can also read from the...
