There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
i am transferriing data between pc and nrf52 dk using nrf libuarte async tx. only the first 5 bytes are sent correctly. after 5 bytes the rest is corrupted. I am trying to...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi all,
Project description and what works:
in my project I have one nRF52840DK as central and three nRF52DK as peripheral. The code on the central is based on the " nrf52...
Hello,
I stumbled over the following problem in configuring an nrf connect sdk project: Somehow I must have dreamt that the Nrf52 UARTs support also baud rates beyond 1mbps...
Hi, I am looking to implement Azure IoT Hub and Azure FOTA in a project. Unfortunately these examples are specifically for the nRF9160. I would like to implement it on the...
I am currently trying to connect an accelerometer to my Nordic board, but I am having some issues with #define NRFX_TWI_INSTANCE(id)
.p_twi = NRFX_CONCAT_2(NRF_TWI, id)...
My problem is with examples of publishing and subscribing at the same time. I crossed them by adding a check for subscription if I did not sign I do this and register the...
Hi guys. I'm fairly new at embedded development and I'm basically trying to set up a workflow that goes like this:
Toggle a GPIO high - low, with a duty cycle of ~500...
I have been following the "Getting started with Nordic's Secure DFU bootloader, a step by step guide". I believe I may have compiled and loaded a DFU bootloader to the nRF52840...
Good afternoon,
I'm working on troubleshooting an issue we're having in the field. We are using the CLI libraries to provide an nRF52840-based board with an interface to...
Hi all,
I need to directly develop my application on top if IEEE 802.15.4 MAC layer. Could you please inform me of any sample application available under Zephyr that directly...
Device: nRF52840
SDK: 16.0
Softdevice: ANT_s340_nrf52840_6.1.1
Hello, We have a master and several slaves setup in a simple master/slave channel configuration. It seems...
Hi,
Can u suggest the procedure to implement key refresh procedure with the sample network using nrf mesh app.
No where i found option in nrf mesh app.
Thanks in Advance...
Hi,
We have 2 projects in pre-production stage that use nRF52840. We are also using FreeRTOS for both projects.
Now we need to create an OTA bootloader for both. There...
