Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi eveyone.
I want to trying this example,but i used nrf connect and nrf toolbox doesn't see the DEVICE_NAME.(SDK 16)
please tell me what happened.
by the way.I use...
Hi,
I have some questions regarding errata 136.
I understand that the workaround is to ignore reset reason bits which are not RESETPIN .
However, I don't understand...
Hello,
I am trying to transfer firmware packages in sequence (SD , BL & APP) to iOS device. I am using button less DFU without bonds. iOS device could able to transfer only...
Hello everyone,
I am working with nrf52832 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine. Whenever...
When I try to increase the CENTRAL_LINK_COUNT to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max connections...
Hi All,
I have a device configured as i2c master, The device is sending 1024 byte of data to NRF52832 DK continuously in form of 255-bytes packet. But I observed that I...
Hello,
I am trying to get the nrf sniffer working to test the ble connection between my 9160DK board and thingy52 board. Some custom software running on both board and...
Hi all,
I am currently experimenting with the gps sample and I would like to adjust the AGPS data update interval.
As far as I understand, in the gps sample, is set to...
Hi,
we are using nRF52840 in our project, we also set some configuration like below snapshot
Here it comes 185uA, we want to know what is the overall consumption means...
Hi ,
I am working on the nRF52 Dk Kit and running the example code- found on the folder \ble_central_and_peripheral\experimental\ble_app_interactive. This is command line...
As you will see with my simple files I have followed about 3 different tutorials to get to the point I am at. I am trying to replace the included SALSProbe.ino program with...
Hello,
I'm trying to program an nrf52 PCB I created from Arduino and code studio just trying to upload a simple blink but when ever I try to connect any of my ST-link...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
