Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I have an NPM1300 demo board. After testing, the default voltage of VOUT1 is 1.74 V. If I use this voltage to power the VDD of nRF54L15, will it affect the power-on reset...
Hi Nordic
We plan to use 54l15+7002e, how much storage will spend for nRF7002 up layer stack and application(e.g typical Wi-Fi STA with TCP client connections)?
What I've tried:
Testing Summary: SD Card on Port 2
Setup : Wired an SDHC card (Transcend 8GB) to the Connector P2 (middle header) on an nRF54L15 DK v1.0.0...
In my code, I find I can start up the ble pakage sending. but it alway send out without stop. I need send out one package. and stop. In my radio callback. I do call this task...
Hi Nordic Support Team,
I am working on a Matter application using the nRF54L15 , and I have a few questions regarding the external flash configuration.
I noticed that...
nRF Connect SDK v3.2.1, nRF9160dk
Hi,
I'm working on an application which connects to a MQTT broker over cellular network, and have MCUMGR enabled for firmware updates...
Hi，
There are 8K functions in nrf_desktop, but this example is too complicated. My own example is relatively simple. I want to integrate 8K functions. At present, overlay...
I am using the nRF54L15 (PANB511 Module ) controller with an ST7789V-based display connected via SPI21 at 8 MHz. Image bin files are stored using LittleFS in external flash...
Hi,
I'm trying to modify the Nordic sample apps included in the ESL Getting Started kit so that the tags first scan for Access Points (APs) so that they can connect to the...
Our IoT device is connecting to 2 different cell towers on the same carrier. Cell tower 'A' has signal of -90dBm, tower 'B' has signal of -105dBm.
The device is mainly attempting...
Hi,
I am using nRF54L15 with SDK v3.0.2 . I am facing an issue while initializing the LSM6DS3 sensor on a custom PCB.
Device Initialization Code:
#define...
I am developing a modbus server application for nrf54L15 in nrf sdk v3.2.3. But I ran into an issue where using MODBUS_MODE_ASCII requires UART_CFG_DATA_BITS_7. The modbus...
Dear Nordic,
The west build system is not acceptable for firmware development.
Firmware != Software. When we create firmware for a product, it must last for years. We...
