Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
I am using nRF connect SDK v2.9.0 with a custom developed board that looks like this:
I tried the ' Bluetooth LE LED Button service' sample as it's and noticed that...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
I have a custom board (nrf5340) and can debug it, but it will not print to J-Link RTT Viewer. The main looks like this and I tested with a breakpoint on the LOG_DBG using...
Hello everybody! It's my first question and I'm new at mcu programming. I hope for your understanding!
I have a task: count seconds using a counter and display them on a...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hello,
I am using a nrf Development kit and I have it plugged in into a mac laptop. It works fine, but I keep getting the message that says:
Disk Not Ejected Properly...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Hello,
I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hi!
I am trying to power the thingy:91 from solar panels and have some issues with the thingy:91 restarting when the solar panel receives a medium amount of light. The solar...
Since I need zephyr version 4.0 or newer, I tried updating my project to the nRF Connect SDK v3.0.0 as well as the toolchain. I know that they are not fully released yet....
