I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi
Could you provide nPM1300 NTC pin inside structure?(pull up resistor value, pull up voltage, others..)
And I want to know how to calculated NTC temperature by measured...
Hello everyone,
We'd like to use the rom_report and ram_report commands to be able to see (with a somewhat granularity) how much ROM and RAM do specific feature use so that...
Hi,
Question on the nRF7002. Can it be used as a hotspot to support 5 -10 wifi clients?
Basically, the need may be to download user manuals on site with a tablet.
...
Description
I was following the tutorial from DevAcademy regarding the setup of the nRF Sniffer for Bluetooth LE : DevAcademy: nRF Sniffer for Bluetooth LE
However, the...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hello,
I am trying to exchange data with an external slave sensor via SPIM communication using the nRF5340DK.
I am currently facing two main issues:
1. The spi_transceive...
I am using the NRF54L05.When I was using the timer function of the Zephyr software, I created a timer with a 10ms cycle. After my system had been running for a long time ...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
Hi,
Can you please guide me if I want to receive a larger message of around 15KB from server, how can I do it using CoAP block transfer in thread.
I am using nRF5 SDK...
Hi,
I built the nrf/samples/bluetooth/hci_lpuart program in SDK v3.1.1. I am using an nRF9160DK board version 1.1.0. I did add several printk statements to zephyr/samples...
Hi Team,
We are working on a commercial pre-production project using nRF5340 and are currently migrating from nRF Connect SDK 2.6.1 to NCS 3.1.1 . We followed the official...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
