Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi DevZone !
I have a problem with the FDS library. I am using it to store configurations of my nRF52840 that I read every time the chip resets I will write in that only...
Hi,
I have a nRF51822 evaluation board and a nRF52833 DK.
Would it be possible to do Bluetooth direction finding with both of them?
I understand that nRF51822 is not...
Hi,
I am trying to measure my circuit sleep current while connected, through a high value resistor, the problem is while waking up each MIN_CONN_INTERVAL the processor wakes...
It is found that under the same routine in zigBee SDK, the project under pCA10056 folder can run normally without burning the protocol stack, but the project under PCA10059...
We would like to stream data through an l2cap channel from a nRF52840 module to a smartphone. The l2cap connection is initiated by the smartphone, I configured an l2cap tx...
I would like to test some compatibility features using the nrf52833 DK as a Bluetooth 4 transmitter instead of Bluetooth 5 (which it is by default). I do not see an explicit...
hi support team，
i have two questions from customer.
1. Monthly review suggested that Verizon certificate will be on October this year, how about he progress, we have...
I'm using the Nordic UART Service to implement BLE communication between an iOS app (central) and a Raspberry Pi (peripheral). Whenever I send a large payload to the central...
Hi,
We are using Nordic thingy 52 HW and their SDK for our Evaluation purpose. We are using Nordic thingy 52 microphone code directly. That firmware is using ADPCM codec...
Unable to connect to Bonded weara with GATT 133 error. Currently, there is only one solution, turning on and off Bluetooth in the OS, which temporarily improves the connection...
Hello
new nRD5 SDK v17.1.0
Can you please help me to find more about:
1. "- NRFFOSDK-13484: Added an option in the Peer Manager to decide that a connection will not...
Hello,
I am currently developing an application on a single core application. I need to add a BLE part to this application. Currently, I have an OTA update procedure that...
Hello,
I'm trying to open an L2CAP connection and send some test data to the nrf52840 dev board from my computer. But my connections were timing out with 'Page Timeout'...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
