Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello. I'm designing a board with NRF52832 connected to SGTL5000 via I2S. I'm planning to use the driver found in the Nordic Playground here...
https://github.com/NordicPlayground...
Hello,
Before going into detail, the question is: Is there is any chance that NAND flash will be supported (via QSPI or SPI) by the nRF5 sdk in the future ?
My question...
I made all of the functions using nrf52832, s132. Now I want to reduce the current consumption.
So, I tried changing the slave latency. It was confirmed that the current...
When I combine BLE_APP_UART + BLE_APP_UART_c apps in last step "ble_nus_data_send" return error 4 from BLE_APP_UART part in multirole mode
BLE_APP_UART_c send without problem...
Hi,
I am working on having my device to perform a dfu over spi. I have been able to get through the init packet initialization and transfer, however, I am getting an error...
If my device only acts as a peripheral, does it need to respond to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST events? In other words, is BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST a...
Hello,
I added bonding to my BLE central device so I can re-establish known connections very fast. The bonding of the devices works fine but additionally I would like the...
Hi all,
I am using ncs version 1.5.0 and dk version 0.15.0.
I would like to rely on the CC310 piece of hardware to perform some cryptographic computation.
However, I...
Hello.
I have a question about setting MAC address.
For now, my device uses random static address from FICR.
And I also use "bt_set_id_addr()" function for test purpose...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
