Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello
SDK ver 17
DK nRF52 DK
DK is a peripheral connected to many centrals. Every time I connect to a phone I get the messages attached in the picture.. My question...
Hello, support team:)
Currently I am working on SPI communication with LSM6DSOXTR.
CLK, MOSI, SS is working as expected. But there is no MISO signal.
0) All SPI...
Hi,
Just would like to know is it possible to proceed auto pairing by restore the MAC address of host?
The current idea is using direct advertising to speed up the pairing...
Can a provisioner work as a client connect to a server
how do I set on the phone app(iPhone 10s)
in example/light_switch I did not do any change on the example
...
Hi,
I'm in the process of integrating nrf52840 module in HCI over UART to a linux host.
So far I have been able to build the hci_uart in from the samples and bring it...
Dear Members,
How can I share GPIO pin between SPI and I2C peripheral ?
I see SCK_PIN and MISO_PIN for SPI are the same with SCK and SDK on I2C
#define SER_APP_SPIM0_SCK_PIN...
For reference I am using the nRF5 SDK version 17.0.2. I have been comparing the flash_placement.xml files in the <SDK>/config directory and in some of the examples. I have...
Hi. I am looking for simple example of using QDEC for nrf5340. I want to use the Segger Embedded Studio.
Where can I find the example of some guide for HW driver for nrf5340pdk...
i am using nrf52833 development kit here i am using peripheral template as for coding purpose when i merge temperature sensor(SSTS751) code and W25Qxx code in it then the...
I am trying to build the connectivity hex files on an ubuntu build machine for an nrf52840 dongle so I can communicate with another nrf52840 dev board, I followed the instructions...
Hello, my project has 3 different devices (2 sensor and flash memory) on the same SPI bus all with their own CS. I ran across the following question , which has a response...
Hi ,
My environment :
nrf connect sdk
nrf5340 dk
segger studio IDE
verified method 1:
As per nrf5340 product specification document , we can protect the...
Hello,
I was recently trying out some samples with the nRF9160 DK and I had run into some issues when trying to run the nRF Cloud Client Application .
I had flashed...
