Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi!
If I build my project with TF-M I noticed that at least the flash usage report differs dramatically compared to the original firmware:
Original:
Memory region |...
Hello
I am currently porting nRF52833 using SPI communication with other MCU (AD5940).
AD5940 provides an example of porting with stm32, which we are referring to.
Currently...
The document nRF52811_PS_v1.0 states that the Threshold Voltage Tolerance of the Power Fail comparator is typically +/- 1% and max. +/-5%.
Under which circumstances does...
Please tell me the UICR setting in nRF52810 and S112. Currently, when I develop with nRF52810 and S112, the area of UICR is 0xFF. [1]The oscillator is equipped with 32MHz...
Hello.
I'm working on disconnecting ble from the module.
I'm using the app provided by nordic.
I designed it to disconnect the ble when I press the button on the module...
hi.,
we develop a product that use nrf52840,and it need to suport usb dfu in windowns and mac.and also need achieve cdc communication .this funcation is ok in windows,and...
USED SDK: v1.4.99-dev1
USED BOARD: nRF9160DK
Received hexvalues above 0x7F (decimal = 127) are counted double in p->message.payload.len Any ideas what might be te problem...
We are trying to evaluate the BLE Mesh for a product range and are evaluating the nRF52832 for the same.
Working with the nRF Mesh SDK, I am facing some issues, which are...
Under the recommended operating conditions (page 611) in the nRF52840 datasheet, there is a note specifying:
Given a device (with SWD access), is there any way to detect...
Hello Sr,
Take a look below Error, when I run the demo code from
C:\..\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\multiprotocol\ble_thread\ble_thread_dyn_mtd_coap_cli...
Hi,
We have created an application with BLE multi peripheral where I have to put my chip into deep sleep mode by long pressing the tactile button & also I have to wake it...
In the nRF51822, there was a bootloder area, but in the nRF52810, there is no area except for Application, and the image is as shown in the map below, is that correct? --...
