Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
SDK51 appears to be an inconsistency with how various BLE related events are handled in the SDK. Multiple BLE event handlers may be registered using the NRF_SDH_BLE_OBSERVER...
I'm currently implementing a DFU "controller" in C on the nRF9160 for performing serial DFU with the nRF52840 and believe I have discovered a bug.
My firmware image was...
Hi
I'm using nrf52 DK with SDK V17.0.0
Currently, I'm using Single Buffer to send Data through BLE.
However, I want to use Double Buffer instead of using Single Buffer...
I might be dense here, but please bear with me and clarify something. I am looking at the SPI bus as drawn on the nRF52840. According to the schematics (PCA10056 - nRF52840...
Hello,
Background: I have a custom board that contains nRF52832 module and exposes UART pins (RX, TX, RTS, CTS). I have developed an application using nRF5 SDK v17.0.2....
I'm using SDK 17.0.2 And I found that when the Scan timeout is not working,
Debugging I found that when the nrf_ble_scan_on_timeout function is called, the source of the...
I have an nRF5340 development kit. I can flash a custom application into the app processor. However, when I try to flash the peripheral_lbs sample, I'm getting the error shown...
The hrs.c has the following code.
/* Heart Rate Service Declaration */ BT_GATT_SERVICE_DEFINE(hrs_svc, BT_GATT_PRIMARY_SERVICE(BT_UUID_HRS), BT_GATT_CHARACTERISTIC(BT_UUID_HRS_MEASUREMENT...
I have added the following modification to "ble_app_hids_mouse" example for pca10040 s132.
I want to add a peer whose IRK is known as follows,
void peer_add() { memcpy...
Hello, guys.
We are have nRF52840DK board and Zephyr NCS 1.4.2 development environment.
I am trying to include two PWM channels in the code and control them independently...
Still haven't seen coded phy support with nRF Connect for Desktop for receiving advertisements. With the fact that support from devices is slim, how are we suppose to test...
Hi, Currently I am working on a sensor project with nrf52832. I am having problems optimizing the battery so let me ask the whole circuit as below when the operation will...
Hi,
We want to develop a tracking system using nRF51822 for that we need clarifications for the below,
Can we make BT connection as shown below fig?
Do we need to include...
The Dev Board has a connector J1 to connect an external aerial, I want to check the long range BLE feature. Are there any PCB modifications required to the PCB to use this...
