Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
HI Team,
We are using the nRF52840 DK for our development purpose. We have some issues with USB J2 connector and unable to connect the on board debugger. We have tried...
Please note about 9 days ago another user reported similar problem but is his case LED3 and LED4 were blinking. In my case after reset I see LED 3 blink and then about 30...
It had been working fine until just this moment.
Every time i turn it on, it works fine for few seconds and then the red led in the device turns on. I don't understand the...
Hi,
I'm developing for a 52833 using SDK_17.0.0 and S113_7.0.1.
I'm using the following code with the intention that when the RDY pin goes low, it will wake up the processor...
Hi! I'm currently using the nrF52840 DK to send numbers by BLE. I have 2 questions for you. 1. Can I send negative values? ex. -1, -2, -3 2. Can I send decimal values? ex...
Hi Nordic Support
I have been working to port a blinky variant project and have found previous threads useful for guidance. I'm working with Segger Embedded Studio and have...
Hello,
Is there a way to multicast messages from BLE client to multiple servers? I know mesh does the same job but we are exploring a possibility to do the same using standard...
hi,I am working with nrf52832 board. I want to send the multiple beacon at a time(same instance).
can you please suggest me at a a time how many beacon we can send out(exact...
Let me first show what parameters I am choosing for calculating the data rates :
Conn interval is 7.5ms and connection length ext is off meaning it wont extend the connection...
Hello,
Application crashes at " nrf_sdh_enable_request ()" without returning any error code. Execution up to this seems fine and I get RTT debug prints. I have also tried...
In a timeslot-based multi-protocol application running on an nRF52832 with Softdevice S132 7.0.1, at seemingly random points and very rarely I observe the softevice calling...
There is an error in your documentation here:
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.0/lib_bootloader_dfu_banks.html?cp=7_1_3_5_1_2_2#lib_bootloader_dfu_appdata...
Hi, I need to support both BLE update and serial update with sdk 17. Going through some past post, the idea is clear.
1) Start with DFU_BLE example project.
2) Add the...
From my understanding, notifications have guaranteed in-order delivery at the lower levels. I'm working on a small file transfer system out of an nrf52840, trying to decide...
Dear Sir/Madam,
As a BLE solution in our products one of the candidate ICs is NRF52820. Our current PCB is a 2 layer one. But the reference design for NRF52820 is 4 -layer...
