Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I have used BMD301 BLE chip. I have connected one wifi chip "ESP02" with BMD301 chip via UART.
I am using nRF5_SDK_15.3.0_59ac345 for my ble application firmware...
Hi,
we have a nRF52 DK getting sensor values from a Sensor connected as SPI-Slave. Everytime there is a new Sensor Value (~20 ms) the sensor generates an Interrupt and pulls...
Hi,
While upmerging our project from SDK 15.3.0 to 17.0.0 we faced an issue in the sdc_handler due to usage of a NULL pointer.
In the case SDC_EVT_INIT if the p_event...
Hello,
I am experimenting with PWM for time, I have a setup where I am using three sensor which gives analogue output.
I am using a mux which has two control pins, so...
Hi all
I have just started doing some work with the nRF52840- DONGLE (and hence nRF52840-DK) and am new to Nordic devices, tools, BLE, etc.
Basically for my first application...
I'm attempting to increase the size of the TX Queue in an effort to increase notification performance.
I'm using nRF52840 with an S140 soft device. I use Segger Embedded...
Hi,
I have two nRF9160DKs and I noticed that the SHA-256 digest of the credentials looks very strange
Questions:
1, Why are the digest so repeating? I have installed...
I'm implementing the door lock cluster on the server side (the door lock device), and needs to send event commands to the client (door lock controller/gateway) . According...
Hi Team,
We are using the NRF52832 for our application and we have enabled the crypto libraries for that.
For,
1. AES-ECB,CFG,CBC modules we are using the "mbed TLS...
Hello,
We are using nRF52840 with SDK 15.2.0. In our software we have handled the DTM and we are able to send the commands using UART.
We would like to do the receiver...
Hi,
I'm developing a Bootloader for the nRF52xx chip using the SoftDevice S113 v7.0.1 and SDK v17.0.0
Looking into the infocenter I've seen that there's a possible mistake...
I have an AWS account and I am comfortable with the AWS IOT operation in general. I have used it in the past. I am trying to get the sample mqtt_simple to connect to AWS IOT...
