I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hello,
From the documentation I read that Softdevice can support maximum 20 BLE concurrent connections. How does Nordic determine this maximum number of 20 and is this arbitrary...
I see the SWD debug port is a 2-wire protocol, SWCLK and SWDIO. My debugger device has two additional pins, SWO and nReset. Are these two pins required to debug and program...
I PURCHASED A SIM OF THE THINGHS MOBILE BECAUSE IBASIC DOES NOT WORK.
I HAVE LAUNCHED ASSET TRACKER AND THE NRF9160 DOES NOT CONNECT. LTE FLASHES IN YELLOW.
IS THERE A...
I was checking DFU through serial usb/uart on the following link:
infocenter.nordicsemi.com/index.jsp
I want to double check if this entire project is for programming...
Hi,
While linking I am getting the following error on Nordic SDK 16.0,
XYZ.axf: Error: L6218E: Undefined symbol nrf_ble_gq_conn_handle_register (referred from ble_db_discovery...
Hi everyone,
I am new to segger embedded studio. I want ibeacon firmware sample code to advertise uuid, major, minor, tx power, advertisement interval. I want to change...
We're developing a product where a single NRF52840 board - lets call it the central- serves as the focal point for multiple NRF52840 boards spread out across an area - lets...
I am not able understand the difference between APPROTECT and BPROT . Can you please clarify ? and if we enable the protection then how to disable it again whenever we want...
I've seen many posts about LL_LENGTH_REQ causing disconnection on certain Android phones and the solution from Nordic is to add a 100ms delay. Can someone from Nordic definitively...
Hi community,
in our setup we use the LSM6DSL IMU using TWI. First we initialize the TWI peripheral, then we configure the IMU. After that we initialize PPI to automatically...
I am trying to build the project "thingysdkv210" which is downloaded from https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms/Nordic-Thingy-52/Download#infotabs...
nRF52 DK
HTS example
I added app_timer_stop_all() in the ble_evt_handler() of main.c, under the case of BLE_GAP_EVT_DISCONNECTED, but the battery service timer still...
need help on multiple things
All work is on the DK 840 board using sdk15.3
Started with this link
https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic...
Is it possible to run the Zigbee Light Switch example with the internal RC.?
On the sdk_config.h I have changed the following:
#define NRFX_CLOCK_CONFIG_LF_SRC 0
But...
