Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
I'm trying to implement the NRF5340 as an I2C slave. The current answers all show the answer as old to look for a newer answer. Were implementing the NRF5340 as a slave to...
Dear all,
is it planned to update the declaration of conformity of nRF9160 from EN 301 908-13 V13.2.1 to EN 301 908-13 V13.3.1?
EN 301 908-13 V13.2.1 is only valid until...
I am currently working with the Aliro 1.0.0 from nRF Door Lock and Access Control Add-on.
I need to know how to properly configure or set custom data fields for Aliro protocol...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
I am attempting to get familiar with the NDEF support on the nRF54L15 DK. After creating a copy of a sample based on the WRITABLE_NDEF_MSG example, I create a build configuration...
Hello Nordic Support Team, I am developing BLE content, where nodes will be periodically uploaded to the gateway.During this interval,the CPU needs to be kept idle, waiting...
Hello DevZone,
I have wrote a standard Zephyr display driver for one customer, I used sQSPI and Zephyr MSPI API.
I finished the development, but the QSPI (1-1-4 mode)...
Hello,
Our product (sports timing) will be used at the upcoming Olympics and our customer is being asked some questions about wireless specs. We use Bluetooth 5 (backward...
Hi,
I have a custom nRF52832 PCB with 10 buttons connected to various GPIOs. All buttons work correctly except the two connected to P0.07 and P0.08 they produce no response...
Hi,
“ We are designing our board with the nRF54LM20, and both the SPI/QSPI and UART peripherals can operate independently and be mapped to separate GPIOs.in QFN-52 Package...
I am working with the DTM sample on nRF52840 using nRF Connect SDK (Zephyr) .
My goal is to run a continuous TX test automatically at boot (standalone) , without requiring...
My Setup and Environment We have built a custom PCB with an nRF5340 and an nRF7002Q Wi-Fi module. I have attached the relevant schematics for the PCB.
We are using the nRF...
HI
I'm having an issue where VS Code cannot recognize the SDK and toolchain. Everything was working fine before, but now errors occur when I open VS Code and try to build...
