hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Anybody got any hints at how to get Zephyr to work on the nrf52840 PCA10059 dongle?
After many struggles, I was finally able to compile Zephyr's sample/bluetooth/hci_usb...
Hi there,
I am trying to get I2C communication up and running with the nRF52832 (specifically configuring the nRF52832 as a master to communicate with 3 slave devices),...
Hello everyone,
I am developing a temperature and gas sensor for indoor environment monitoring. Due to the limitation of the bluetooth transmission range, I hope to add...
Hello, I am developping on a nrf52840-DK board and try to debug using a Black Magic probe. Software is based on softdevice, GCC build chain and Visual Studio Code with Cortex...
I've been wrestling with this DK for some time now, but today I tried to get the LTE Link Monitor app to run and see what outputs I could get. I ran everything the same as...
Hi,
I am having issues, getting the uart backend logging working on a nrf52840 dongle. I'm testing the logging on the standard blinky example that came with the sdk (15...
Hi,
Upgrading from nrfConnect for Desktop from v 2.6 to v 2.7 and higher and its associated apps seems to hang on Linux (ubuntu 16.04). 'strace' suggests that the problem...
I have a design which mainly needs to be a peripheral, however I was told that I need to use the multi-pheripheral example as I may need the device to switch to a central...
I'm attempting to get Eclipse and the GNU Arm toolchain installed on my Windows 10 system. I'm following the instructions at...
https://devzone.nordicsemi.com/tutorials...
Hi All
I am a newbie with the nRF52 series SoC's and my end goal is to make a solar powered weather station.
I have a very crude nRF52832 dev board that I program with...
Hi, team.
There is a connection nfr52840 and esp32 (115200, 8, no parity, flow disable).
I'm using UARTE in interrupt mode (to send AT command and receive responses)....
Hi there, I am using the MDBT50Q-1MV2 Raytac module, with the nRF52840, and i have noticed that I have a very noisy VDD supply pin. Which definitely a problem because measures...
The qspi driver seems to make a number of assumptions about the protocol that don't fit the Winbond W25M02GW (and certain other) SPI flash chips.
Two major issues I've run...
I'm developing on an nRF52832 that has a serial connection with an iMX6 that is running a Python script with pySerial. For a while I had flow control disabled and would get...
