hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I have read that bootloader can switch between two applications if programmed at different locations in flash by user. So how exactly bootloader knows to which application...
Hi,
I would be grateful if you advise on the OAuth client id's required when developing the android nrF beacon for Eddystone.
From reading the nrF beacon for Eddsytone...
Hi I have had problems when trying to update the relay status of a server node in my mesh app which is a combination of the light switch server proxy and dfu examples (plus...
Hi!
We are using the nRF52840 and nRF52832 for a product for which good data throughput over BLE is required. (We have picked the S140 and S132).
We send these data using...
Hi,
I'm trying to use RTT Logging in my application. If I build and flash my application through Segger Embedded Studio RTT logging works. However If I use ARM GCC to build...
I'm not able to carry out monitor mode debugging. I'm referring https://github.com/NordicPlayground/j-link-monitoring-mode-debugging/blob/master/pca10040/s132/arm5_no_packs...
Hello.
I almost finish nrf52-quadcopter develop.
I want fly drone with mobile.
I want to confirm PID value from minum to maxium in mobile.
and I want to confirm your...
Hello Nordic team
I am working on nRF52840 DK, SDK-15.0.0 with ble_central example. I need to give support of DFU like we are doing with ble_peripheral example.
My question...
Hi, I have a question for you! Thank you!
My PCA10040 was not successfully connected to the computer.
The device manager of the computer did not show anything related...
Hi
i am using SDK15.0 .i have tested Secure Ble for firmware update. Its working with my public keys. i want to know is it possible to update firmware without Public key...
Hello,
I am trying to find the IP address of the devices.
Device: nRF52840 DK
Setup: Running virtual Ubuntu 18.04 inside Windows 10 (using VMWare).
I am able to connect...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
