hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Using SDK14.2.
I'm trying to optimize the throughput of my ble_nus-based app (I'm getting about 5k/sec right now). I've read elsewhere on this forum that increasing NRF_SDH_BLE_GAP_EVENT_LENGTH...
Hi.
I am trying to program the ble beacon application example that requires the S132 softdevice. I am following the instructions that request the device be erased first...
Hi,
I'm looking for feedback on the feasibility of using Bluetooth Mesh to network Bluetooth modules in a series of adjacent hotel rooms. All the nodes are also relays since...
Hi!
I have a Nordic nrf51822-DK. I'm need send large data to the Android phone (10 mb).
I'm use sample devzone.nordicsemi.com/.../dealing-large-data-packet-s-through-ble...
This may not be the place to ask this question but have to start somewhere.
1. Using an Adafuit BLE Sniffer nRF51822.
2. Ble-sniffer-osx, Version 1.2. 4 (build 28)
3...
According to the answer here , Nordic currently doesn't offer a proxy node implementation.
What would be the best way of getting started to create a proxy node? Are there...
Hi,
My device is peripheral and server and is connected to an (android) phone. I have two related questions:
a) I understand that maximal packet size is obtained by calling...
Hi!
I'm trying to log the flow of communication in the Light Control example of the Mesh SDK. But when I log all the received network messages on a server, I also get a...
Hello
I would like to check coded phy performance
in order to do so I need to achive the following:
1. change to coded phy on default (as I ub\nderstand can by...
I am getting BLE working on an nRF52832, and I am a bit confused as to what I should be setting RADIO->CRCINIT to. I was hoping someone could clear this up, which is more...
Hello
I m trying to measure the current in my development card nrf52DK using the power profiler kits, so i prepared the board by (cut the PCB track shorting solder bridge...
Hello,
I am using the NRF52-DK softdevice 6.0.0 and NRF SDK 15.0. The app is based on on the ble_app_template PCA10040e S112 (The final chip will be a NRF52810 that's why...
I want to flash the program in my custom board. I have flash the program in nrf52832 BLE module via j-link using nrf52832 development board. So, how do i confirm that the...
I use the SDK S110, I hopes in the low power(operation the current 100 uA is following), and then sustains every second bluetooth broadcast and every second computing time...
Hello,
I am using sdk 12.2.2 and customised nrf52 board.
My challenge is when I am using sofdevice + app hex file my device takes 4.1 uA current but when I am uploading...
