Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
I am using an nRF52833 in a project where and i want to be able to update it via another mcu (STM32H7) over uart. The STM32 has received and saved the new hex file...
Hi, I have a custom NRF52840 board that I need to send EMG data via BLE with. Only has SWD, no usb-c data link unfortunately.
I am using version 1.6.1 of Adafruit NRF52...
I was reading the Errata document for the NRF54L15, and came across this: 3.18 [37] POWER: Current consumption might increase after pin reset or power cycle. So I was wondering...
I'm testing the NRF54L15 radio and found an issue. When I set the radio to BLE 2Mbps mode, I received data from adjacent frequency bands. For example, I set the radio's receive...
Dear experts, I am programming bare metal using Segger Embedded Studio and nrf.h and want to achieve a simple example of network core sending data to the application core...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
Hello:
I'm watching the Structuring nRF Connect SDK Projects for Flexibility and Scale webinar. I'm following the hands-on video step by step. When using "Create a New Board...
Hi,
I'm currently facing an issue with my nRF52840 chip acting as the transmitter connected to a BLE broadcasting device. One client uses a voice recorder product that requires...
Hi Support Team
We want to use the J-Link of nRF54L15DK to program customer's nRF54L15 board. We follow the guideline of below link to connect the Pins of P19 of nRF54L15DK...
I am trying to connect waveshare e-paper 4.2" display to my nrf54L15, I am currently running a peripheral uart sample code on the board and my plan is to build the project...
At least one of the errata defines in the HAL headers is ignored by the driver implementing the device.
e.g. the following line claims to control whether the workaround...
Hey all!
I've just received my first board with a Nordic chip. More specifically it features the Ezurio BL54L15µ module.
I am currently "limited" to programming via SWD...
hi
I am using periodic_adv_conn and periodic_sync_conn from the NCS 3.0.0 SDK.
After periodic_sync_conn reports data to periodic_adv_conn in the corresponding time slot...
We are considering to develop an embedded device that can control Matter door locks. So it should act as a Matter Door Lock client. Unfortunately it is impossible to find...
