Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello to everyone!
I bought nRF54L15-DK for Matter Over Thread developing and prototyping.
Before nRF54L15 I tried ESP32C6 XIAO + Arduino IDE and it worked but it was...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
Hi all
I am very new to BLE development and I hope that this question was not asked before in another way.
Is this example also available in nRFConnect with another name...
I'm using an nRF52840 microcontroller on an electronic board to read from and write to an S25FL064 flash memory chip. I'm currently using the nRF5 SDK . Before I could read...
I am trying out the Nordic Bluetooth ESL sample example code from the link [ Getting started with bluetooth-esl-and-periodic-advertising-with-responses-pawr ]
Downloaded...
I understand from many posts that the DTS file is ignored when in multi-image (mcuboot enabled) I need to change the partitions to reduce the bootloader from 48K to 32K &...
Hello Nordic Support Team,
I’m currently experiencing issues connecting to my nRF52833 hardware. The device was previously working without problems, but now I’m unable to...
Hello, I am currently developing with NRF52840 and NRF7002 chips. I am running a custom version of the wifi scan sample, using the baremetal library and custom shim file....
Hello,
I wanted to check if it’s possible to use the BLE Mesh light code with other BLE Mesh apps such as ST BLE Mesh, Bluetooth Mesh, or AMCCOM Mesh.
I have tested it...
I am taking some courses from DevAcademy to learn about Zephyr.
I do have some zephyr supported board(s) for the hands-on exercises, but they are STM32 based, not nRF
...
I note that calling:
mpsl_lib_init causes the POWER . INTENSET to be cleared (including the USB interrupts and POF WARN).
My device uses the USB stack, as such, calling...
Hi,
I'm trying to combine Wifi and BLE frequency test on nRF7002 DK. I started with radio_test example on nRF SDK 2.9.1 and toolchain 3.0.2.
I have added CONFIG_NRF70_RADIO_TEST_COMBO...
Hi.
When I made a application with mcuboot on nRF54L15DK.
In order to reduce power consumption, I want to disable serial log(UART).
I added these configuration in the...
Hello,
We have successfully connected a team device and are receiving telemetry from nRF Cloud via MQTT. We subscribe to prod/{team_id}/m/# and receive all team messages...
