why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
Hi,
For the first time iOS App interface with BLE device. But after killing and re-opening of iOS App connection not established. Can anyone share me the code from iOS App...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
Dear, I have bought the nRF5340 DK. I have installed nRFConnector and Segger Studio. Now, I want to test Blinky project. I connected a USB cabel to USB connector which is...
I have a receiver , transmitter application. I use a custom board as transmitter. I would like to use pca10040 as receiver but currently i use it as debugger to my custom...
Hi,
Our company has produced a batch of BLE products, and the 10uH inductor model used above is SDFL2012S100KTF. The rated current is not as large as the current value...
Hi,
I close the uart log and open the rtt log
why uart log can be used still?
why rtt log display error state?
I set the log config like this:
I set the test...
hi
i have this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_timer_cnt_get (referred from max30105.o).
in this code part.
the example is...
I have a program that runs great on the dev kit, however after uploading the code to a custom board based on the nRF52810, it does not seem to run.
I upload the code by...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
