why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
I'm trying to flash the firmware to some custom built pcb's with NRF52840 on it. The first time I flash it, it works great.
Then, if I try to erase the chip (or any...
Hello
I have this firmware running in C:\Users\danie\ncs\v1.5.1\nrf\applications\tracker on the nRF9160-DK, nRF9160 SICA B1 is the marking on the chip
Modem FW is...
Hi. Some questions regarding the nRF9160 ENABLE pin:
1. According to the nRF9160 product specification the ENABLE pin voltage requirements are like this:
In the first...
Is it possible to add additional UI for different sensors in nrfcloud platform ? I could see that there is a predefined list of sensor types that can be attached to cloud...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. I would like to measure the time required to send a message from client to server...
Hi all,
I'm working on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v3.2.0%2Fthread_example_dfu.html
I'm struggling on the server part, I...
Hello,
we are developing a verry small sensor node. Since we like to know if the sensor we are connected to, is one of our sensors instead of an attacker fake sensor we...
Hi! I was testing GPIOTE with pin_change_int example and tried to add a log to the push of the button.Somehow the code is not working, it is indeed changing the state of the...
nrf52840, sdk17. pca10056 (for now). linux arm-gcc, gnumake, etc.
I have a fairly complex PPI configuration but in the act of debugging it, I've dumbed it down quite a...
How does the interrupt latency compare between COMP/LPCOMP and GPIOTE? Are t LPCANADET and t PROPDLY the correct field to be looking at in the specification? The electrical...
Hi Nordic Team,
My Board: nRF5340 DK; SDK: nRF Connect SDK v1.5.0
I am new to BLE developement. I am trying to design a GATT service which can be accessed by nRF Connect...
I'm trying to use UART flow control and assign RTS CTS pin numbers.
What's the corresponding number for P0.02, P1.15 each?
And where can I find this information?
Hi,
I have used nRF52811 SoC in my custom design. In this circuit i have used SWD interface only as per reference design. I have used same SWD 10 pin connections as mentioned...
128 MHz or 64 MHz operation is mentioned in the specification (page ii). However, can MCU be capped at around 12MHz? How about the current consumption?
