Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag). I can able to control led's using customized board. But Bluetooth is...
I am using the gazell protocol of nrf52840,how to use broadcast radio mode from host to device based on the gazell protocol ?or can I use the gazell protocol to make it possible...
We have an neural network running on a 52832 using the floating point unit. We started encountering FPU exceptions so we enabled the FPU IRQ to identify which specific instructions...
Hi everyone,
I want to create multiple USB instances using only one nRF52840 dongle. I want to implement one CDC ACM class instance and another one instance that has two...
Hi,
I have a problem with floating point types on nrf9160.
I get an exception when I get to a simple floating point assinment:
void f(int i)
{
float x;
x = (float...
Hi everyone!
I'm new using Nordic Semiconductor products, I have a Nordic Thingy 91 running Asset Tracker application by default.
I want to test only specific things first...
I was thinking of using the nordic thingy:91 for monitoring purposes in seismic areas.
To this aim, I would need to have some sensors deployed in the environment which:...
Hi,
I need to use nrf_dfu_settings.c to detect external firmware in Bank 1 during application boot. I also need to use Falsh Data Storage to save application parameters...
Hi All,
I'm working from the Thread CLI example, and I got a network of multiple thread devices that works just fine (they see each other, and can send/receive messages...
Hi there,
I'm trying to do a basic test with the GPIO/NMOS - just trying to turn an LED on and off for now. We're going to be doing this in response to the outcome of an...
Hello,
I'm working on the mqtt_simple sample in zephyr environment for NRF9160 board.
We tested the firmware with 2 sim cards with different packets: IPv4 and IPv6,...
azure_iot_hub_connect does the following check:
connect_client looks like this:
If the embedded return at line 40 of connect_client occurs (as I've seen it do) then...
I noticed on Zephyr docs this:
nRF5340 PDK (preview development kit) is an earlier version of the nRF5340 DK. nRF5340 PDK board is deprecated and is replaced by nRF5340...
Hi Nodic,
I try to add the tx power to both the connection mode and advertisement mode to make it long range available. But when I run the code it fails.
Please check...
Hi.
I do not find the description about I-Cache principles and work algorithm.
I read the part of the documentation "NVMC - Non-volatile memory controller". I think, I...
