Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hi all
I am working on Bluetooth application using NRF52840 kit. The application is very simple, the device would have about 7 push buttons which when pressed data will...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
Hi
I have some questions that need your help.But it seems that there is no answer yet.The following is my questions link.
https://devzone.nordicsemi.com/f/nordic-q-a/52060...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
Hi to all,
I am using nRF52832 DK with SDK 15.0 version. My two nRF52 DK damaged while debugging I am a little bit confused why this happening.
When I debugging I used...
Hi,
I need a way to dynamically disable watchdog when I do MMD debugging. I found the old trick, check bit 0 on CoreDebug->DHCSR, does not work any more in MMD. Is that...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
I followed the suggestions in https://devzone.nordicsemi.com/f/nordic-q-a/51642/can-t-build-nrf-connect-asset-tracker
But, still having the same issue.
Using tag v1.0...
On one of our products, we are experiencing approximately 4% failures during production. I traced the problem to be caused by function sd_softdevice_enable not returning....
Hi Devs,
based on this example
https://github.com/NordicPlayground/nRF52-Bluetooth-Course
i was able to run it, and the value field appear below the Unknown Characteristics...
