Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Dear All,
I would like some advice with regards to the best practice with configuring and controlling the nRF9160 M1/NB1 connection.
When working with other modems, our...
I need to implement a Real Time Clock and I want that clock to be updated even when the device is switched "off".
I understand the RTC is a Real Time Counter rather than...
In our setup several devices are suddenly not working anymore, power off and power on is not working. However, if I connect the debugger it suddenly starts working.
So the...
Hello,
I'm trying to compile a slightly modified version of the template application for nRF52832 using Segger Studio. I'm running into a compile issue with this line utilizing...
Hi,
In "ble_app_uart" project, the system will enter sleep mode after 3 mins.
When system enter sleep mode, the "RTT view" will print following message.
How to modify...
I am trying to open example project(nrf9160, assent tracker project) with SES V4.20a(download form nrfconnectSDK instruction)
1. It doesn't recognized header files.
2...
hi all ,
now , i need get gps latitude and longitude information.
reference nrf9160_gps.c file,it should be do it now ,
how to use driver to get PVT? ,
follow , it...
Hello ,
I use SDK 15.3 , chip is 52811
I refer to the example of 52840 "examples \ peripheral \ timer"
The following is the example code, I have not changed it.
...
Hi, I am trying to debug firmware on the nRF PCA10059 usb dongle board, through a nRF10056 dev kit by attaching a standard 10 pin header on the usb dongle at P1 & connecting...
Hi everyone
Program crashes after few minutes while trying to run two threads(GPS thread and a thread used for caculating the battery voltage) simultaneously.
Please...
Hi,
I am trying to understand how the connection parameters and settings work and how they change the throughput. For this sake, I have been experimenting with the ble_app_att_mtu_throughput...
Hi everyone,
I few days I tried run on my NRF9160 DK CC310 hardware RSA crypto functions.
When I started it at first I ran security_service demo where board run random...
Hi,
When I write a very simple USB audio device that just pass a sinuous wave created in a timer that runs at a 16KHz freq - how can I tell "someone" on the host listens...
Hi,
I'm wondering if there are any samples that show how to use sleep mode on the nRF9160. Not quite sure where to start to look for resources on this. Any documentation...
