Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
Dear Sir,
I have enabled my project for SPIM+EasyDMA.
I am configuring the SPIM transfer nrf_drv_spi_xfer with additional flags like,
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER...
nRF51822 QFAA
At first I set up the RAM size to 0x1F80, it works fine. However, after I try to use RTT to print log, I got the compile error: region RAM overflowed with...
Hi ... how to set the password to secure the connection between the device and application . I don't want to anyone to connect my device , for that i am planning to the set...
I have a nRF52 DK. I'd like to debug my board which has nRF51822 and sensors, and has SWCLK, SWDIO, VCC, GND, RX, TX, VCC, GND. Please provide detail steps on how to wire...
I'm developing a central that discovers services in a peripheral. The services are both custom and standard BLE services. Discovery is working fine, but there is one issue...
Hello,
We are experiencing a rare condition whereby we read in raw Accelerometry data (758 bytes) over the SPI bus, and sometimes (rarely), we'll get a block of repeated...
Hello Everyone, I designed and fabricated a small nRF52 board. The design of this board is based on the Adafruit nRF52 feather. The difference between my designed board and...
Hi,
I'm working on MacOS 10.14.6 and I'm having trouble with the Programmer app in nrf Connect.
I have installed the Jlink driver successfully (v6.60a), but when I select...
