I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Hey All,
I'm using the nrf52840 for gathering device information from Bluetooth devices having an nrf52 chip on board. The application runs through connect/disconnect...
PROBLEM:
My nRF24L01 transceiver occasionally stops working (about every 2 minutes) when receiving and transmitting data packets.
I found that when the power supply occasionally...
I'm looking at the secure boot in the sdk for nrf52840 and have noticed that nrf_bootloader_flash_protect uses the ACL to protect the MBR and the bootloader from being overwritten...
Hi,
I know it sounds ridiculers, but i just can not flash bootloader into 52840.
I am under S140 v610, SDK v15.2.
I started using open_bootloader in example ( pca10056_usb_debug...
hi,
We are working on nRF9160 DK board.
One of the issues is how to save secure data (e.g, data key) into flash. Is there any examples or document on data storage APIs...
Hello,
i am developing on nRF52840 using SDK 15.2.0 and Softdevice 6.1.1.
I recently noticed, that when i first bond with the nRF52840, then disconnect and delete the...
Hello,
I am using nRF52840 development kit and I wanted to know with use of the source code of nRF blinky application can i modify as per my project requirement and make...
I am connecting debug out on the NRF52 DK to a production board for programming. I am using Tag Connect connection and need to make sure I route pins properly. I cannot find...
Good morning,
I'm developing a new product based on nRF52840 and S140 (v6.1.0). I'm able to connect using my smartphone using the following data:
sec_param.bond = SEC_PARAM_BOND;...
Hi, sorry for if this has been answered elsewhere.
I am currently designing the production setup for a product using the nrf52840 as a BLE radio.
I can't find how the...
Following this tutorial: www.novelbits.io/.../ some doubts arose in my head.
My doubts concern Android app witch name is: nRF Mesh. This application is used only for Provisioning...
Our BLE DFU has stopped working in SDK 3 so I have tried to simplify it by going back to SDKs.
If I compile D:\NordicSemi\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\Examples...
Hi, I have a question about Bluetooth mesh secure provisioning, as it is described in the spec section 5.4.3.
The spec states that either
1) both OOB public key exchange...
We are looking to implement "dynamic" BLE services that can be configured (i.e. enabled/disabled) externally, however from the examples there appears to be no way of de-initialising...
