Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm developing a device using mqtt+tls referring the link here.
https://devzone.nordicsemi.com/f/nordic-q-a/48407/how-to-use-mqtt-tls-in-nrf9160
When I add CONFIG_NEWLIB_LIBC...
How can I add security middleware, between connection request device and my connectable device.
I want to that if one device sent connection request to my device, I want...
Hi, I am evaluating two nRF52832 boards with a PCA10040. I am using the SDK examples Central and Peripheral to talk to each other on Tera Term. I am using the "send file"...
Hi,
We have implemented the reference design of the NRF24L01+. Our tests results in a low range (about 6 meters), we excepted a multiple of that (about 1 kilometer).
I...
We have connected a 50 Ohm Antenna with NRF52832-QFAA-R7, but we tested and found the antenna signal is weak. Could anyone help to provide some proposals for how to improve...
Hi,
I have a STM32 MCU and I want to flash this MCU by using an nRF52840. The two chips will be connected by UART.
From where I need to start, and what is the most easiest...
When attempting to connect to an MQTT broker set up on my local machine using the mqtt simple sample code, I get this output:
What does this error code mean? Also, is...
Hi. We are using the nRF52 sdk v12.1 with S132 v3.0.0 on a nRF52832. Once in a while (could be after running a few hours, could be after running a week) the application ends...
Where can I find the right documentation to start understanding the Nordic Thingy FW? Do we have any design document for this?
I need to develop my own application on the...
Hello,
I'm looking for some general guidance on the following application:
1 nRF52840 based gateway to cloud, on power supply
a few hundred nRF52832 sensor nodes,...
We want to use app_timer_create/app_timer_start to create a periodic timer, but noticed that there were a few seconds missing. After printing out each tick, we see that there...
I can't open my tickets since it's changed into private ticket by your engineer.How can I do?
My ticket' name is"about service change can't receive BLE_GATTS_EVT_WRITE"...
Hi,
I will work with nRF51822. I installed all software tools and I connect target device with debugger.
Should I connect nRF51822 with power like battery (because I will...
