Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I guess my question is stupid, but I would like to ask it by the way..
in all ble examples we use a function for handling ble events by our app
in my case in example ble_app_uart...
I'm trying to launch my app on a custom board with nrf52 after a successful launching on DK. The problem is here: err_code = sd_softdevice_enable(p_clock_lf_cfg, softdevice_fault_handler...
Hi folks, I'm making progress with a program to get two nRF24L01p modules communicating with each other, but there are a couple of remaining problems. I hope someone can help...
I have a little bit of experience on TI BLE stack development and wanted to move to Nordic product with Bluetooth or ANT protocol for a higher data rate. I got a general question...
Hi All,
I have a problem with .hex file. I use example ble_app_uart from nRF5_SDK.
In examples\ble_peripheral\ble_app_uart\pca10056\s140\armgcc I executed: make all and...
I try to turn off the system with sd_power_system_off()
// Go to system-off mode (this function will not return; wakeup will cause a reset).
err_code = sd_power_system_off...
Based on 'ble_app_template' in nRF5_SDK_12.2.0 (S132), I develop a program with nRF52832.
The problem is that the program will restart after reaching APP_ADV_TIMEOUT_IN_SECONDS...
Hi,
I have a few questions about using floating point in nRF5 chips. As discussed here , nRF51 has no FPU but we can simply use "float" in Keil and have the operations...
My device as a slave, if the surrounding environment is not good, the unknown master device connected to my slave device caused the real master device to be unable to scan...
Dear Nordic family,
I tried programming MDBT40 (purchased from Raytac ) with the same code which worked with nRF51822 Bluetooth Low Energy BLE 4 and 2.4GHz Wireless Communication...
I'm trying to implement a simple RTC timer into my project, and it seems like the app_timer module is the best way to do that, especially when using the Softdevice. I added...
Hello,
we are facing the following issue when using Android and trying to rebond with a previously bonded S110 peripheral:
Bonding the Android device with the S110 based...
We are looking to store a unique name and number in each device as it is provisioned from the factory, and are considering using the UICR. We are using something close to...
