Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Is there any way to print all SDK documents at once?
I'd like to print all of the SDK v12.0 Documents and carry it with in offline,
But I can hardly find any PDF Document...
Hi.
I'm trying to figure out how to properly use GPIO pins, but so far I did not find a document explaining how to use GPIO with nrf included functions.
I found bits and...
I am using nRF51 (PCA10028) DK and nRF51 SDK v9.0.0 for Development. I want to merge all three DFU(BLE + SERIAL + ANT). i have merge BLE and SERIAL DFU code. For this i have...
Hi,
I merged 3 hex files(softdevice.hex, bootloader.hex, application.hex)
I uploaded this hex file to nrf52382 DK.
After uploading hex file to DK, although there...
Hai
i have the following queries about pairing / bonding in nrf51822.
can i retrieve the bonding information from flash memory. if so how can i do that..?
if a...
Hi
Last year I got a nRF52 devboard and I modified the ble uart peripheral example to flash a led depending on what it recieves from nRF uart app.
It all worked fine(after...
Hi,
I'm trying to use the SPI example from the SDK 11 to comunicate with a MPU accelerometer.
The first time it works well, but then the clock send only 8 peak, so the...
FIrst timer with the nordic.. so i could use some help.
i've tried my code on the eval kit and it worked fine. On my custom board (has external 16MHz crystal www.digikey...
I've come across a couple of products that shows up as both classic and BLE. But when connecting to these products via nRF Connect or inspecting the traffic, I can't seem...
From reading the reference manual, product specification as well as searching the developer zone: here and here . Is it correct that the AVDD pin supply's ONLY the radio....
I have a strange problem with the secure bootloader.
After a succsessful DFU update of firmware, the firmware starts, but resets after a short while (about a second). ...
Hi,
While I'm Flashing LED Blinking Example in nRF51822 Ek using Keil uVision 5 along with SDK v12.2.0 , Program is uploaded but LED is Continuously glowing without blinking...
Hi
I have been trying to make a dual bank serial dfu bootloader with security features for nrf51822 (board 10028), but seems the UART/HCI dfu support is missing in SDK...
