Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hello,
I am testing the ble_peripheral example of ble_app_uart (SDK 12, soft device 130), this has been asked at a lot of places that the MTU is limited to 20.
But then...
Hi,
I am using nRF51822 and implemented timer-2 with 2 sec capture/compare interrupt rate. But if I want to read timer's current count before it generates interrupt or...
at nRF51 SDK v9.0.0, S130, PCA10040, at peripheral side
If we receive a characteristics less than 20 bytes, we can get the correct handle value(like 0x3B). And then everything...
I bought nRF51-DK yesterday.
I installed nRFgo Studio(1.20), Keil uVision(5.15), Softdevice s110 (8.0.0), J-Link(5.00),
nRF51 MDK(7.2.1)
I turned on the nRFgo studio...
Hi,
I'm using Eclipse Mars 5.2 on Windows 10 along with the GNU Toolchain as described in the "Development with GCC and Eclipse Tutorial" by Vidar Berg (Thanks very much...
Hi, I can't get SPI slave mode working on nRF51822. I'm using the Core51822 module with a BLE400 board from Waveshare and up to date mbed. SPISlave::receive() always returns...
I implement it with sdk 11.0 and a third party core-board.Firstly,I program s132_nrf52_2.0.1 SoftDevice by nRFgo Studio,then I open ble_app_hrs s132_with_dfu(arm4) project...
Hi,
Currently I'm using internal RC osciallator for LFCLK on the system that run on CMSIS-RTX and Softdevice S110 and it doesn't have external 32K crystal.
The RTC os...
Hello,
I just received an NRF52DK today. I was able to run the demo (LED blink/Switch and NFC) which comes factory installed. But copying the hex files from demo (proximity...
In the picture, the usb pcb is PCA10000, the circle PCB is the product PCB.
The diameter is 20mm.
Chip antenna is used now but the distance is 5m in 4dbm TX.
Here...
Hi all,
I would like to design a product based on the nRF52832 chip. The board should have an accelerometer, a charging circuitry for a LiPo and some additional components...
Hi there,
I am done with TI and the new IDE and Stack 2.2
May be anybody can point me to the right IDE and chip to replace my TI CC2640 4x4 designs to Nordic semiconductor...
Hello,
I would like advertise for an unlimited time.
Why value 0 in ble_gap_adv_params_t::timeout don't work ? Device don't advertise anything. It works fine with a positive...
