hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I am trying to control the smart phone function while making my device as HID keyboard, but It seems that the soft keyboard (smart phone on screen keyboard) clashing...
i think your nrf51 iot sdk don't have rpl functionality....
if i want to implement rpl on it what is the procedure...
if i want rpl on raspberry pi what is procedure......
i have bluetooth usb 4.0 dongle..which part of bluetooth stack it contains...?to support simultaneous master and slave connections will it need any firmware update...?
...
As we known we can set static passkey in peripheral side (s110) with the API sd_ble_opt_set(BLE_GAP_OPT_PASSKEY, &ble_opt) as below:
inline void setPassKey(void)
{
uint8_t...
I've tried all 4 versions of the HID Mouse Example provided through the Keil Pack Installer tool and can't seem to get any of them working.
The code compiles and downloads...
I was trying to compile the example code(nRF51 SDK8.0) for ANT and flash to my nRF51DK(pca10028) board, but the example code was not working on my board. I tried compiling...
Hello.
I'm now writing a software based on nrf51_sdk_v6_1_0/nrf51822/Board/nrf6310/s110/ble_app_hrs. The SoftDevice I'm using is s110_nrf51822_7.1.0_softdevice.hex. Why...
So I've been using a user submitted SD safe TWI implementation that I found here. This has worked well so far, but upon updating to SDK 8.0.0 parts have broken. Now when I...
Hi,
I'm using the NRF51DK which comes with the nFR51422. I initially flashed the board using the ble_uart example.
Since then I've tried flashing it with other examples...
Since we have some performance problems with sd110 V7.0.0, we tried a upgrade to v8.0.0.
This version(8.0.0) with IC revision 3 solved our performance problems:).
But a...
Hi,
I am working on a project regarding a portable device for healthcare monitoring. This device will have a nrf8001 module integrated that will communicate with a iOS...
Hello there,
I know that the range of the possible BLE communication depends on the internal configuration as well as on the external environmental conditions.
I would...
I downloaded the zip file from Git Hub Nordic.. and extracted it into C:\Keil_v5\ARM\Pack\NordicSemiconductor\nRF_Examples\7.1.0\ble_peripheral\
When I open the project...
Hi~
I have a nrf51822 EK board(PCA10001 V2.2.0), but the J-link OB can't flash 51822 chip.
The situation is:
1.I can see Segger J-link on segger software&nrfgo studio...
Hi all,
I've been trying to get a new Win 7 (x64) PC setup with with the Nordic dev tools.
Studio, MCP, SDK etc.
I've installed Studio (1.17.1) and MCP (3.7.1). This...
